| @g.delgaudio:matrix.org | Hello everyone, | 12:36 |
|---|---|---|
| I believe this is the right thread; if not, I kindly ask ildikov to point me to the correct one. | ||
| I have installed STX version 10 (24.09). My current setup is a Central (All-in-One Duplex) and an edge cloud with a Standard with Controller Storage + 2 Workers. | ||
| I need to add some Debian packages to the edge cloud. To do this, I followed the guides below to create a patch to be applied on the edge cloud. | ||
| I set up a build environment, added my library to the .lst files, and downloaded the packages. So far, everything works fine (https://docs.starlingx.io/developer_resources/build_guide.html | ||
| ). | ||
| Next, as described in this guide, I created a recipe to add my Debian package (https://docs.starlingx.io/developer_resources/starlingx_patching.html | ||
| ). | ||
| After generating the patch and uploading it (sudo sw-patch upload 001.patch), I am unable to apply it as shown in the guide. | ||
| The upload works weel but i cannot apply the patch to the nodes on the edge cloud. | ||
| Has something changed, or does STX 10 support another method? | ||
| Thank you very much. | ||
| @g.delgaudio:matrix.org | * Hello everyone, | 12:38 |
| I believe this is the right thread; if not, I kindly ask ildikov to point me to the correct one. | ||
| I have installed STX version 10 (24.09). My current setup is a Central (All-in-One Duplex) and an edge cloud with a Standard with Controller Storage + 2 Workers. | ||
| I need to add some Debian packages to the edge cloud. To do this, I followed the guides below to create a patch to be applied on the edge cloud. | ||
| I set up a build environment, added my library to the .lst files, and downloaded the packages. So far, everything works fine (https://docs.starlingx.io/developer\_resources/build\_guide.html | ||
| ). | ||
| Next, as described in this guide, I created a recipe to add my Debian package (https://docs.starlingx.io/developer\_resources/starlingx\_patching.html | ||
| ). | ||
| After generating the patch and uploading it (sudo sw-patch upload 001.patch), I am unable to apply it as shown in the guide. | ||
| The upload works well but i cannot apply the patch to the nodes on the edge cloud. | ||
| Has something changed, or does STX 10 support another method? | ||
| Thank you very much. | ||
| @ildikov:matrix.org | Giuseppe Del Gaudio: This should be the right room, thank you for sharing all the details about the challenge you're facing. | 13:24 |
| @ildikov:matrix.org | Was there any specific information in the error messages or logs about the reason applying the patch didn't work? | 13:25 |
| @ildikov:matrix.org | scott.little: Do you know if anything has changed in how patching works compared to the above linked guide? | 13:29 |
| @g.delgaudio:matrix.org | It seems that at the moment the suggested command is not available in the STX 10 CLI. Here is the sequence of commands: | 14:16 |
| @ildikov:matrix.org | Giuseppe Del Gaudio: Thank you for sharing. There is a new Unified SW Management framework in StarlingX that was introduced in 10.0. It seems like it replaces the commands that you've been using: https://docs.starlingx.io/r/stx.10.0/releasenotes/index.html#appendix-commands-replaced-by-usm-for-updates-and-upgrades-835629a1f5b8 | 15:42 |
| @g.delgaudio:matrix.org | Thank you, I’ll do some tests tomorrow and let you know. | 16:01 |
Generated by irclog2html.py 4.0.0 by Marius Gedminas - find it at https://mg.pov.lt/irclog2html/!